-- *****************************************************************
-- Descriptions of managed objects for ADSL DMT line interfaces.
--
-- September 1999, Patrick Gili
--
-- Copyright (c) 1999,2000 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-IDSL-LINE-MIB DEFINITIONS::=BEGINIMPORTSInteger32,Counter32,Gauge32,MODULE-IDENTITY,OBJECT-TYPEFROM SNMPv2-SMI
TruthValue,VariablePointer,TEXTUAL-CONVENTIONFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ciscoMgmt FROM CISCO-SMI
ifIndex,InterfaceIndexFROM IF-MIB
PerfCurrentCount,PerfIntervalCountFROM PerfHist-TC-MIB
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
AdslLineProfileName,adslLineConfProfileName FROM ADSL-LINE-MIB
;ciscoIdslLineMIB MODULE-IDENTITYLAST-UPDATED"200001200036Z"-- January 20, 2000 12:36 AMORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco System
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
Tel: +1 800 555-NETS
E-mail: cs-dslam@cisco.com"DESCRIPTION"This MIB module describes IDSL (ISDN Digital Line Subscriber)
line interfaces. The structure of this module resembles that
of the ADSL-LINE-MIB (RFC-2662). Observe that the tables in
this module do not necessarily extend the tables defined by the
ADSL-LINE-MIB. Currently, only those tables that contain
configuration information extend the profile tables defined by
the ADSL-LINE-MIB. This allows the management client to define
xDSL configuration profiles that apply across all xDSL modems,
independent of the technology being utilized by the modem.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
ADSL - Asymmetric Digital Subscriber Line.
ATM - Asynchronous Transfer Mode.
BRITE - Basic Rate Interface Terminal Extender.
CV - Coding Violation.
DLC - Data Link Connection.
DSL - Digital Subscriber Line.
ES - Error Second.
IDSL - IDSN Digital Subscriber Loop.
ITU-C - IDSL Transceiver Unit, Central Office end.
ITU-R - IDSL Transceiver Unit, Remote terminal end.
LMI - Link Management Interface.
LOF - Loss Of Frame.
LOS - Loss Of Signal.
NT - Network Terminator.
PPP - Point-to-Point Protocol.
PPPoA - PPP over ATM.
SES - Severely Errored Second.
*** DEFINITIONS ***
CODING VIOLATION
A coding violation occurs when the incoming signal exhibits
a CRC anomaly.
DOWNSTREAM
The flow of data in the direction from the ITU-C to ITU-R.
ERRORED SECOND
A second with one or more coding violations.
LINE RATE
The total data rate supported by a line. Observe that the
payload rate is equal the line rate for the earliest
implementations of IDSL. However, the payload rate maybe
less than the line rate for future implementations.
SEVERELY ERRORED SECOND
A second with 3 or more coding violations.
UPSTREAM
The flow of data in the direction from the ATU-R to ATU-C."REVISION"200001200036Z"-- January 20, 2000 12:36 AMDESCRIPTION"Initial revision of this MIB module."::={ ciscoMgmt 154}-- Textual ConventionsIdslPerfTimeElapsed ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return the
maximum value."SYNTAXGauge32IdslPerfCurrDayCount ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"A counter associated with interval performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this counter starts at zero at the beginning of an
interval and increases when associated events occur, until the
end of the 1-day interval. At that time, the agent stores the
value of the counter in the previous 1-day history interval,
if available, and resets the value of the counter to zero.
In the case where the agent has no valid data available for this
interval, the corresponding object instance is not available.
In this case, the agent will respond with the appropriate error
indicating that the instance does not exist; that is,
'noSuchName' in response to a SNMPv1 get request, and
'noSuchInstance' in response to a SNMPv2 get request."SYNTAXGauge32IdslPerfPrevDayCount ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"A counter associated with interval performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this counter is equal to the current day counter
at the end of its most recent interval.
In the case where the agent has no valid data available for this
interval, the corresponding object instance is not available.
In this case, the agent will respond with the appropriate error
indicating that the instance does not exist; that is,
'noSuchName' in response to a SNMPv1 get request, and
'noSuchInstance' in response to a SNMPv2 get request."SYNTAXGauge32-- MIB Object DefinitionsciscoIdslLineMIBObjects OBJECTIDENTIFIER::={ ciscoIdslLineMIB 1}-- IDSL Line TablecIdslLineTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslLineEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains the common attributes describing both ends
of IDSL lines supported by the system."::={ ciscoIdslLineMIBObjects 1}cIdslLineEntry OBJECT-TYPESYNTAX CIdslLineEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"A set of common attributes describing both ends of an IDSL line
supported by the system. There exists an entry for each ifEntry
with an ifType of idsl(154)."INDEX{ ifIndex }::={ cIdslLineTable 1}
CIdslLineEntry ::=SEQUENCE{
cIdslLineSpecific VariablePointer,
cIdslLineConfProfile AdslLineProfileName,
cIdslLineAlarmConfProfile AdslLineProfileName
}cIdslLineSpecific OBJECT-TYPESYNTAXVariablePointerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies an object identifier of an instance of
an object in the MIB. The implementation determines the
application of this object. For example, an implementation
may use this object to provide a reference to the port-class
physical entity (see the ENTITY-MIB for further details)
corresponding to the IDSL line."::={ cIdslLineEntry 1}cIdslLineConfProfile OBJECT-TYPESYNTAX AdslLineProfileName
MAX-ACCESSread-write
STATUScurrentDESCRIPTION"This object specifies the row in the adslLineConfProfileTable
(see the ADSL-LINE-MIB for further details), which applies for
this IDSL line interface.
In the case the implementation utilizes 'dynamic mode' (see
the ADSL-LINE-MIB for further details), then the value of this
object defaults to the name of a configuration profile
designated by the implementation as the default configuration
profile.
In the case the implementation utilizes 'static mode', then the
the value of this object is read-only."::={ cIdslLineEntry 2}cIdslLineAlarmConfProfile OBJECT-TYPESYNTAX AdslLineProfileName
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object specifies the row in the
adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further
details), which applies for this IDSL line interface.
In the case the implementation utilizes 'dynamic mode' (see
the ADSL-LINE-MIB for further details), then the value of this
object defaults to the name of an alarm configuration profile
designated by the implementation as the default alarm
configuration profile.
In the case the implementation utilizes 'static mode', then the
the value of this object is read-only."::={ cIdslLineEntry 3}
-- IDSL ITU-C Physical Parameters TablecIdslItucPhysTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslItucPhysEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains physical-layer parameters for ITU-C class
devices supported by the system."::={ ciscoIdslLineMIBObjects 2}cIdslItucPhysEntry OBJECT-TYPESYNTAX CIdslItucPhysEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A set of physical-layer parameters for an ITU-C class device
supported by the system. There exists an entry for each ifEntry
with an ifType of idsl(154)."INDEX{ ifIndex }::={ cIdslItucPhysTable 1}
CIdslItucPhysEntry ::=SEQUENCE{
cIdslItucInvSerialNumber SnmpAdminString,
cIdslItucInvVendorId SnmpAdminString,
cIdslItucInvVersionNumber SnmpAdminString,
cIdslItucStatus INTEGER}cIdslItucInvSerialNumber OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the vendor specific string that
identifies the vendor ITU-C."::={ cIdslItucPhysEntry 1}cIdslItucInvVendorId OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the vendor identifier assigned according
to ANSI T1.220."REFERENCE"ANSI T1.220-1991, Coded Representation of the North American
Telecommunication Industry Manufacturers, Suppliers, and Related
Service Companies."::={ cIdslItucPhysEntry 2}cIdslItucInvVersionNumber OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object specifies the vendor specific version number of
the ITU-C."::={ cIdslItucPhysEntry 3}cIdslItucStatus OBJECT-TYPESYNTAXINTEGER{loopDown(1),dslSync(2),loopUp(3),loopUpLmiActive(4)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the state of the ITU-C transceiver:
- loopDown
The IDSL link is down, as a result of a near-end has
detected a LOS, a LOF, has not exchanged an ACT bit
with the downstream BRITE/NT1, or similar fault/condition.
- dslSync
The IDSL link has achieved physical layer activation with
the first downstream entity (iether a BRITE or the NT1).
- loopUp
The IDSL link has exchanged the ACT bit with the NT1, but
LMI signalling is not yet active. This is the normal
operating state for PPP operation.
- loopUpLmiActive
The IDSL link has exchnaged the ACT bit with the NT1
and the LMI signalling is active. This is the normal
operating state for frame relay operation."::={ cIdslItucPhysEntry 4}-- IDSL ITU-R Physical Parameters Table
-- A future revision may use ciscoIdslLineMIBObjects.3 for the
-- purpose of defining the cIdslIturPhysTable, which will contain
-- physical-layer parameters for ITU-R class devices.-- IDSL ITU-C Channel Parameters Table
-- A future revision may use ciscoIdslLineMIBObjects.4 for the
-- purpose of defining the cIdslItucChanTable, which will contain
-- channel parameters for ITU-C class devices.-- IDSL ITU-R Channel Parameters Table
-- A future revision may use ciscoIdslLineMIBObjects.5 for the
-- purpose of defining the cIdslIturChanTable, which will contain
-- channel parameters for ITU-R class devices.-- IDSL ITU-C Performance Data TablecIdslItucPerfDataTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslItucPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains physical-layer statistics for ITU-C class
devices supported by the system."::={ ciscoIdslLineMIBObjects 6}
cIdslItucPerfDataEntry OBJECT-TYPESYNTAX CIdslItucPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A set of physical-layer statistics for an ITU-C class device
supported by the system. There exists an entry for each ifEntry
with an ifType of idsl(154)."INDEX{ ifIndex }::={ cIdslItucPerfDataTable 1}
CIdslItucPerfDataEntry ::=SEQUENCE{
cIdslItucPerfCVs Counter32,
cIdslItucPerfESs Counter32,
cIdslItucPerfSESs Counter32,
cIdslItucPerfHdlcCVs Counter32,
cIdslItucPerfHdlcAborts Counter32,
cIdslItucPerfHdlcAligns Counter32,
cIdslItucPerfHdlcShorts Counter32,
cIdslItucPerfHdlcLongs Counter32,
cIdslItucPerfValidIntervals INTEGER,
cIdslItucPerfInvalidIntervals INTEGER,
cIdslItucPerfCurr15MinElapsed IdslPerfTimeElapsed,
cIdslItucPerfCurr15MinCVs PerfCurrentCount,
cIdslItucPerfCurr15MinESs PerfCurrentCount,
cIdslItucPerfCurr15MinSESs PerfCurrentCount,
cIdslItucPerfCurr15MinHdlcCVs PerfCurrentCount,
cIdslItucPerfCurr15MinHdlcAborts PerfCurrentCount,
cIdslItucPerfCurr15MinHdlcAligns PerfCurrentCount,
cIdslItucPerfCurr15MinHdlcShorts PerfCurrentCount,
cIdslItucPerfCurr15MinHdlcLongs PerfCurrentCount,
cIdslItucPerfCurr1DayElapsed IdslPerfTimeElapsed,
cIdslItucPerfCurr1DayCVs IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayESs IdslPerfCurrDayCount,
cIdslItucPerfCurr1DaySESs IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayHdlcCVs IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayHdlcAborts IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayHdlcAligns IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayHdlcShorts IdslPerfCurrDayCount,
cIdslItucPerfCurr1DayHdlcLongs IdslPerfCurrDayCount,
cIdslItucPerfPrev1DayMoniSecs INTEGER,
cIdslItucPerfPrev1DayCVs IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayESs IdslPerfPrevDayCount,
cIdslItucPerfPrev1DaySESs IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayHdlcCVs IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayHdlcAborts IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayHdlcAligns IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayHdlcShorts IdslPerfPrevDayCount,
cIdslItucPerfPrev1DayHdlcLongs IdslPerfPrevDayCount
}cIdslItucPerfCVs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-C since agent reset."::={ cIdslItucPerfDataEntry 1}cIdslItucPerfESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-C since agent reset."::={ cIdslItucPerfDataEntry 2}
cIdslItucPerfSESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored
seconds experienced by the ITU-C since agent reset."::={ cIdslItucPerfDataEntry 3}cIdslItucPerfHdlcCVs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC coding violations
experienced by the ITU-C since agent reset."::={ cIdslItucPerfDataEntry 4}cIdslItucPerfHdlcAborts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC aborts experienced
by the ITU-C since agent reset."::={ cIdslItucPerfDataEntry 5}cIdslItucPerfHdlcAligns OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC frames received by the
ITU-C with a non-integral number of octets since agent reset."::={ cIdslItucPerfDataEntry 6}cIdslItucPerfHdlcShorts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of short HDLC frames received
by the ITU-C since agent reset. A short HDLC frame contains
less than 5 octets."::={ cIdslItucPerfDataEntry 7}cIdslItucPerfHdlcLongs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of long HDLC frames received
by the ITU-C since agent reset. A long HDLC frame contains
more than 1500 octets."::={ cIdslItucPerfDataEntry 8}
cIdslItucPerfValidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of previous near-end performance data 15-minute
intervals for which data was collected. The value will be <n>
unless the measurement was (re-)started within the last (<n>*15)
minutes, in which case the value will be the number of complete
15-minute intervals for which the agent has at least some data.
In certain cases (e.g., in the case where the agent is a proxy)
it is possible that some intervals are unavailable. In this
case, this interval is the maximum interval number for which
data is available."::={ cIdslItucPerfDataEntry 9}cIdslItucPerfInvalidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of near-end performance data 15-minute intervals in
the range from 0 to cSdslStucPerfValidIntervals for which no
data is available. This object will typically be zero except in
cases where the data for some intervals are not available (e.g.,
in proxy situations)."::={ cIdslItucPerfDataEntry 10}cIdslItucPerfCurr15MinElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslItucPerfDataEntry 11}cIdslItucPerfCurr15MinCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-C in the current 15-minute interval."::={ cIdslItucPerfDataEntry 12}cIdslItucPerfCurr15MinESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-C in the current 15-minute interval."::={ cIdslItucPerfDataEntry 13}cIdslItucPerfCurr15MinSESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-C in the current 15-minute interval."::={ cIdslItucPerfDataEntry 14}cIdslItucPerfCurr15MinHdlcCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC coding violations
experienced by the ITU-C in the current 15-minute interval."::={ cIdslItucPerfDataEntry 15}
cIdslItucPerfCurr15MinHdlcAborts OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC aborts experienced
by the ITU-C in the current 15-minute interval."::={ cIdslItucPerfDataEntry 16}cIdslItucPerfCurr15MinHdlcAligns OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC frames received by
the ITU-C with a non-integral number of octets in the current
15-minute interval."::={ cIdslItucPerfDataEntry 17}cIdslItucPerfCurr15MinHdlcShorts OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of short HDLC frames received
by the ITU-C since agent in the current 15-minute interval. A
short HDLC frame contains less than 5 octets."::={ cIdslItucPerfDataEntry 18}cIdslItucPerfCurr15MinHdlcLongs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of long HDLC frames received
by the ITU-C since agent in the current 15-minute interval. A
long HDLC frame contains more than 1500 octets."::={ cIdslItucPerfDataEntry 19}cIdslItucPerfCurr1DayElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslItucPerfDataEntry 20}cIdslItucPerfCurr1DayCVs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-C in the current 1-day interval."::={ cIdslItucPerfDataEntry 21}cIdslItucPerfCurr1DayESs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-C in the current 1-day interval."::={ cIdslItucPerfDataEntry 22}cIdslItucPerfCurr1DaySESs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-C in the current 1-day interval."::={ cIdslItucPerfDataEntry 23}cIdslItucPerfCurr1DayHdlcCVs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC coding violations
experienced by the ITU-C in the current 1-day interval."::={ cIdslItucPerfDataEntry 24}cIdslItucPerfCurr1DayHdlcAborts OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC aborts experienced
by the ITU-C in the current 1-day interval."::={ cIdslItucPerfDataEntry 25}cIdslItucPerfCurr1DayHdlcAligns OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC frames received by
the ITU-C with a non-integral number of octets in the current
1-day interval."::={ cIdslItucPerfDataEntry 26}cIdslItucPerfCurr1DayHdlcShorts OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of short HDLC frames received
by the ITU-C since agent in the current 1-day interval. A
short HDLC frame contains less than 5 octets."::={ cIdslItucPerfDataEntry 27}cIdslItucPerfCurr1DayHdlcLongs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of long HDLC frames received
by the ITU-C since agent in the current 1-day interval. A
long HDLC frame contains more than 1500 octets."::={ cIdslItucPerfDataEntry 28}cIdslItucPerfPrev1DayMoniSecs OBJECT-TYPESYNTAXINTEGER(0..86400)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The amount of time in the previous 1-day interval over which
the performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not be
collected for any reason."::={ cIdslItucPerfDataEntry 29}cIdslItucPerfPrev1DayCVs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-C in the previous 1-day interval."::={ cIdslItucPerfDataEntry 30}cIdslItucPerfPrev1DayESs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-C in the previous 1-day interval."::={ cIdslItucPerfDataEntry 31}cIdslItucPerfPrev1DaySESs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-C in the previous 1-day interval."::={ cIdslItucPerfDataEntry 32}cIdslItucPerfPrev1DayHdlcCVs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC coding violations
experienced by the ITU-C in the previous 1-day interval."::={ cIdslItucPerfDataEntry 33}cIdslItucPerfPrev1DayHdlcAborts OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC aborts experienced
by the ITU-C in the previous 1-day interval."::={ cIdslItucPerfDataEntry 34}cIdslItucPerfPrev1DayHdlcAligns OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the number of HDLC frames received by
the ITU-C with a non-integral number of octets in the previous
1-day interval."::={ cIdslItucPerfDataEntry 35}cIdslItucPerfPrev1DayHdlcShorts OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of long HDLC frames received
by the ITU-C since agent in the previous 1-day interval. A
long HDLC frame contains more than 1500 octets."::={ cIdslItucPerfDataEntry 36}cIdslItucPerfPrev1DayHdlcLongs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of long HDLC frames received
by the ITU-C since agent in the previous 1-day interval. A
long HDLC frame contains more than 1500 octets."::={ cIdslItucPerfDataEntry 37}-- IDSL ITU-R Performance Data TablecIdslIturPerfDataTable OBJECT-TYPE
SYNTAXSEQUENCEOF CIdslIturPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains physical-layer statistics for ITU-R class
devices supported by the system."::={ ciscoIdslLineMIBObjects 7}cIdslIturPerfDataEntry OBJECT-TYPESYNTAX CIdslIturPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A set of physical-layer statistics for an ITU-R class device
supported by the system. There exists an entry for each ifEntry
with an ifType of idsl(154)."INDEX{ ifIndex }::={ cIdslIturPerfDataTable 1}
CIdslIturPerfDataEntry ::=SEQUENCE{
cIdslIturPerfCVs Counter32,
cIdslIturPerfESs Counter32,
cIdslIturPerfSESs Counter32,
cIdslIturPerfValidIntervals INTEGER,
cIdslIturPerfInvalidIntervals INTEGER,
cIdslIturPerfCurr15MinElapsed IdslPerfTimeElapsed,
cIdslIturPerfCurr15MinCVs PerfCurrentCount,
cIdslIturPerfCurr15MinESs PerfCurrentCount,
cIdslIturPerfCurr15MinSESs PerfCurrentCount,
cIdslIturPerfCurr1DayElapsed IdslPerfTimeElapsed,
cIdslIturPerfCurr1DayCVs IdslPerfCurrDayCount,
cIdslIturPerfCurr1DayESs IdslPerfCurrDayCount,
cIdslIturPerfCurr1DaySESs IdslPerfCurrDayCount,
cIdslIturPerfPrev1DayMoniSecs INTEGER,
cIdslIturPerfPrev1DayCVs IdslPerfPrevDayCount,
cIdslIturPerfPrev1DayESs IdslPerfPrevDayCount,
cIdslIturPerfPrev1DaySESs IdslPerfPrevDayCount
}cIdslIturPerfCVs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-R since agent reset."::={ cIdslIturPerfDataEntry 1}cIdslIturPerfESs OBJECT-TYPE
SYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-R since agent reset."::={ cIdslIturPerfDataEntry 2}cIdslIturPerfSESs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored
seconds experienced by the ITU-R since agent reset."::={ cIdslIturPerfDataEntry 3}cIdslIturPerfValidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of previous near-end performance data 15-minute
intervals for which data was collected. The value will be <n>
unless the measurement was (re-)started within the last (<n>*15)
minutes, in which case the value will be the number of complete
15-minute intervals for which the agent has at least some data.
In certain cases (e.g., in the case where the agent is a proxy)
it is possible that some intervals are unavailable. In this
case, this interval is the maximum interval number for which
data is available."::={ cIdslIturPerfDataEntry 4}cIdslIturPerfInvalidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of near-end performance data 15-minute intervals in
the range from 0 to cSdslStucPerfValidIntervals for which no
data is available. This object will typically be zero except in
cases where the data for some intervals are not available (e.g.,
in proxy situations)."::={ cIdslIturPerfDataEntry 5}cIdslIturPerfCurr15MinElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslIturPerfDataEntry 6}cIdslIturPerfCurr15MinCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-R in the current 15-minute interval."::={ cIdslIturPerfDataEntry 7}cIdslIturPerfCurr15MinESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-R in the current 15-minute interval."::={ cIdslIturPerfDataEntry 8}cIdslIturPerfCurr15MinSESs OBJECT-TYPESYNTAXPerfCurrentCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-R in the current 15-minute interval."::={ cIdslIturPerfDataEntry 9}cIdslIturPerfCurr1DayElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslIturPerfDataEntry 10}cIdslIturPerfCurr1DayCVs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-R in the current 1-day interval."::={ cIdslIturPerfDataEntry 11}
cIdslIturPerfCurr1DayESs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-R in the current 1-day interval."::={ cIdslIturPerfDataEntry 12}cIdslIturPerfCurr1DaySESs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-R in the current 1-day interval."::={ cIdslIturPerfDataEntry 13}cIdslIturPerfPrev1DayMoniSecs OBJECT-TYPESYNTAXINTEGER(0..86400)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The amount of time in the previous 1-day interval over which
the performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not be
collected for any reason."::={ cIdslIturPerfDataEntry 14}cIdslIturPerfPrev1DayCVs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-R in the previous 1-day interval."::={ cIdslIturPerfDataEntry 15}cIdslIturPerfPrev1DayESs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-R in the previous 1-day interval."::={ cIdslIturPerfDataEntry 16}cIdslIturPerfPrev1DaySESs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-R in the previous 1-day interval."::={ cIdslIturPerfDataEntry 17}-- IDSL ITU-C Performance Interval TablecIdslItucIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslItucIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains physical-layer statistics intervals for
ITU-C class devices supported by the system."::={ ciscoIdslLineMIBObjects 8}cIdslItucIntervalEntry OBJECT-TYPESYNTAX CIdslItucIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 15-miute interval of physical-layer statistics for a ITU-C
class device supported by the system. There exists up to 96
entries for each ifEntry with an ifType of idsl(154)."INDEX{ ifIndex, cIdslItucIntervalNumber }::={ cIdslItucIntervalTable 1}
CIdslItucIntervalEntry ::=SEQUENCE{
cIdslItucIntervalNumber INTEGER,
cIdslItucIntervalValidData TruthValue,
cIdslItucIntervalCVs PerfIntervalCount,
cIdslItucIntervalESs PerfIntervalCount,
cIdslItucIntervalSESs PerfIntervalCount,
cIdslItucIntervalHdlcCVs PerfIntervalCount,
cIdslItucIntervalHdlcAborts PerfIntervalCount,
cIdslItucIntervalHdlcAligns PerfIntervalCount,
cIdslItucIntervalHdlcShorts PerfIntervalCount,
cIdslItucIntervalHdlcLongs PerfIntervalCount}cIdslItucIntervalNumber OBJECT-TYPESYNTAXINTEGER(1..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interval in which the statistics were collected, where the
value of 1 represents the most recent interval, and the value of
96 represents the interval collected 24 hours ago. Intervals
2..96 are optional."::={ cIdslItucIntervalEntry 1}cIdslItucIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies whether the data for this interval
is valid."::={ cIdslItucIntervalEntry 2}cIdslItucIntervalCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-C in the interval."::={ cIdslItucIntervalEntry 3}cIdslItucIntervalESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-C in the interval."
::={ cIdslItucIntervalEntry 4}cIdslItucIntervalSESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of severely errored seconds
experienced by the ITU-C in the interval."::={ cIdslItucIntervalEntry 5}cIdslItucIntervalHdlcCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC coding violations
experienced by the ITU-C in the interval."::={ cIdslItucIntervalEntry 6}cIdslItucIntervalHdlcAborts OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC aborts experienced
by the ITU-C in the interval."::={ cIdslItucIntervalEntry 7}cIdslItucIntervalHdlcAligns OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of HDLC frames received by
the ITU-C with a non-integral number of octets in the interval."::={ cIdslItucIntervalEntry 8}cIdslItucIntervalHdlcShorts OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of short HDLC frames received
by the ITU-C since agent in the interval. A short HDLC frame
contains less than 5 octets."::={ cIdslItucIntervalEntry 9}cIdslItucIntervalHdlcLongs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the number of long HDLC frames received
by the ITU-C since agent in the interval. A long HDLC frame
contains more than 1500 octets."::={ cIdslItucIntervalEntry 10}-- IDSL ITU-R Performance Interval TablecIdslIturIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslIturIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains physical-layer statistics intervals for
ITU-R class devices supported by the system."::={ ciscoIdslLineMIBObjects 9}cIdslIturIntervalEntry OBJECT-TYPESYNTAX CIdslIturIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 15-miute interval of physical-layer statistics for a ITU-R
class device supported by the system. There exists up to 96
entries for each ifEntry with an ifType of idsl(154)."INDEX{ ifIndex, cIdslIturIntervalNumber }::={ cIdslIturIntervalTable 1}
CIdslIturIntervalEntry ::=SEQUENCE{
cIdslIturIntervalNumber INTEGER,
cIdslIturIntervalValidData TruthValue,
cIdslIturIntervalCVs PerfIntervalCount,
cIdslIturIntervalESs PerfIntervalCount,
cIdslIturIntervalSESs PerfIntervalCount}cIdslIturIntervalNumber OBJECT-TYPESYNTAXINTEGER(1..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interval in which the statistics were collected, where the
value of 1 represents the most recent interval, and the value of
96 represents the interval collected 24 hours ago. Intervals
2..96 are optional."::={ cIdslIturIntervalEntry 1}cIdslIturIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies whether the data for this interval
is valid."::={ cIdslIturIntervalEntry 2}cIdslIturIntervalCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of coding violations
experienced by the ITU-R in the interval."::={ cIdslIturIntervalEntry 3}cIdslIturIntervalESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of errored seconds
experienced by the ITU-R in the interval."::={ cIdslIturIntervalEntry 4}cIdslIturIntervalSESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This object specifies the number of severely errored seconds
experienced by the ITU-R in the interval."::={ cIdslIturIntervalEntry 5}-- IDSL ITU-C Channel Performance Data Table
-- A future revision may use ciscoIdslLineMIBObjects.10 for the
-- purpose of defining the cIdslItucChanPerfDataTable, which will
-- contain channel related performance data maintained by ITU-C
-- class devices.-- IDSL ITU-R Channel Performance Data Table
-- A future revision may use ciscoIdslLineMIBObjects.11 for the
-- purpose of defining the cIdslIturChanPerfDataTable, which will
-- contain channel related performance data maintained by ITU-R
-- class device.-- IDSL ITU-C Channel Performance Interval Table
-- A future revision may use ciscoIdslLineMIBObjects.12 for the
-- purpose of defining the cIdslItucChanIntervalTable, which will
-- contain channel related interval data maintained by ITU-C class
-- device.-- IDSL ITU-R Channel Performance Interval Table
-- A future revision may use ciscoIdslLineMIBObjects.13 for the
-- purpose of defining the cIdslIturChanIntervalTable, which will
-- contain channel related interval data maintained by ITU-R class
-- device.-- IDSL Line Configuration Profile TablecIdslLineConfProfileTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslLineConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table extends the adslLineConfProfileTable and contains
IDSL line configuration information."::={ ciscoIdslLineMIBObjects 14}cIdslLineConfProfileEntry OBJECT-TYPESYNTAX CIdslLineConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A configuration profile containing enterprise-specific IDSL
line configuration information."INDEX{IMPLIED adslLineConfProfileName }::={ cIdslLineConfProfileTable 1}
CIdslLineConfProfileEntry ::=SEQUENCE{
cIdslLineConfRate INTEGER,
cIdslLineConfProtocol INTEGER,
cIdslLineConfLmiProtocol INTEGER,
cIdslLineConfLmiNetN392 INTEGER,
cIdslLineConfLmiNetN393 INTEGER,
cIdslLineConfLmiNetT392 INTEGER,
cIdslLineConfUpcIntent INTEGER,
cIdslLineConfBcDefault Integer32}cIdslLineConfRate OBJECT-TYPESYNTAXINTEGER{rate144k(1),-- 144 Kbpsrate144kIdl(2),-- 144 Kbps, IDL formatrate128k(3),-- 128 Kbpsrate64k(4),-- 64 Kbpsrate56k(5)-- 56 Kbps}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the desired line rate."::={ cIdslLineConfProfileEntry 1}cIdslLineConfProtocol OBJECT-TYPESYNTAXINTEGER{frf(1),pppMuxCisco(2),
pppMuxIetf(3),pppLlcIetf(4)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the layer 2 protocol to be employed
by the line, and more specifically the encapsulation type:
- frf
Specifies the frame relay layer 2 protocol defined by
FRF.8. Observe that the encapsulation can be selected
per virtual circuit.
- pppMuxCisco
Specifies the PPP using Cisco proprietary virtual circuit
multiplexed encapsulation.
- pppMuxIetf
Specifies the PPP using virtual circuit multiplexed
encapsulation defined by RFC-2364.
- pppLlcIetf
Specifies the PPP using the LLC (Link Layer Control)
encapsulation defined by RFC-2364."REFERENCE"The Frame Relay Forum, Document FRF.8. Frame Relay/ATM PVC
Service Internetworking Implementation Agreement, April 14,
1995.
IETF RFC-2364. PPP Over AAL5."DEFVAL{ frf }::={ cIdslLineConfProfileEntry 2}cIdslLineConfLmiProtocol OBJECT-TYPESYNTAXINTEGER{
noLmiConfigured(1),lmiRev1(2),ansiT1617D(3),-- ANSI T1.617 Annex DansiT1617B(4),-- ANSI T1.617 Annex Bitut933A(5),-- CCITT Q933 Annex AansiT1617D1994(6)-- ANSI T1.617a-1994 Annex D}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object identifies the local inband signaling protocol."REFERENCE"ANSI T1.617-1991. Integrated Services Digital Network (ISDN) -
Signaling Specification for Frame Relay Bearer Service for
Digital Subscriber Signaling System Number 1 (DSS1).
ANSI T1.617-1994. Integrated Services Digital Network (ISDN) -
Signaling Specification for Frame Relay Bearer Service for
Digital Subscriber Signaling System Number 1 (DSS1).
ITU-T Q.933 10/95. Integrated Services Digital Network (ISDN)
Digital Subscriber Signaling System No. 1 (DSS 1) - Signaling
Specifications for Frame Mode Switched and Permanent Virtual
Connection Control and Status Monitoring."DEFVAL{ noLmiConfigured }::={ cIdslLineConfProfileEntry 3}cIdslLineConfLmiNetN392 OBJECT-TYPESYNTAXINTEGER(1..10)UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the interval between successive status
enquiry messages."REFERENCE"ANSI T1.617-1991. Integrated Services Digital Network (ISDN) -
Signaling Specification for Frame Relay Bearer Service for
Digital Subscriber Signaling System Number 1 (DSS1)."DEFVAL{2}::={ cIdslLineConfProfileEntry 4}cIdslLineConfLmiNetN393 OBJECT-TYPESYNTAXINTEGER(1..10)
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the value of the network-side error
threshold."REFERENCE"ANSI T1.617-1991. Integrated Services Digital Network (ISDN) -
Signaling Specification for Frame Relay Bearer Service for
Digital Subscriber Signaling System Number 1 (DSS1)."DEFVAL{2}::={ cIdslLineConfProfileEntry 5}cIdslLineConfLmiNetT392 OBJECT-TYPESYNTAXINTEGER(5..30)UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the value of the network-side polling
verification timer."::={ cIdslLineConfProfileEntry 6}cIdslLineConfUpcIntent OBJECT-TYPESYNTAXINTEGER{pass(1),
tagDrop(2),tag(3),drop(4)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the default UPC (Usage Parameter Control)
action for connections that do not explicitly specify a UPC
action."DEFVAL{ pass }::={ cIdslLineConfProfileEntry 7}cIdslLineConfBcDefault OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the default BC (Committed Burst Size)
for connections that do not explicitly specify a BC."REFERENCE"Section 6.5.19, 'Link Layer Parameters', ANSI T1.617-1991.
Integrated Services Digital Network (ISDN) - Signaling
Specification for Frame Relay Bearer Service for Digital
Subscriber Signaling System Number 1 (DSS1)."DEFVAL{0}
::={ cIdslLineConfProfileEntry 8}-- IDSL Line Alarm Configuration Profile Table
-- A future revision may use ciscoIdslLineMIBObjects.15 for the
-- purpose of defining the cIdslLineAlarmConfProfileTable, which
-- will contain IDSL line alarm configuration information.-- IDSL PPPoA Performance Data TablecIdslPppoaPerfDataTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslPppoaPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains PPPoA statistics for those ITU-C class
devices configured for PPP operation."::={ ciscoIdslLineMIBObjects 16}cIdslPppoaPerfDataEntry OBJECT-TYPESYNTAX CIdslPppoaPerfDataEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A set of PPPoA statistics for an ITU-C class device configured
for PPP operation. There exists an entry for each ifEntry that
meet the following criteria:
1) The ifEntry has an ifType of idsl(154);
2) The profile associated with the ITU-C class device specifies
a value of 'ppp' for the cIdslLineProtocol object."INDEX{ ifIndex }::={ cIdslPppoaPerfDataTable 1}
CIdslPppoaPerfDataEntry ::=SEQUENCE{
cIdslPppoaPerfRTOs Counter32,
cIdslPppoaPerfCVs Counter32,
cIdslPppoaPerfShorts Counter32,
cIdslPppoaPerfLongs Counter32,
cIdslPppoaPerfDiscards Counter32,
cIdslPppoaPerfValidIntervals INTEGER,
cIdslPppoaPerfInvalidIntervals INTEGER,
cIdslPppoaPerfCurr15MinElapsed IdslPerfTimeElapsed,
cIdslPppoaPerfCurr15MinRTOs PerfCurrentCount,
cIdslPppoaPerfCurr15MinCVs PerfCurrentCount,
cIdslPppoaPerfCurr15MinShorts PerfCurrentCount,
cIdslPppoaPerfCurr15MinLongs PerfCurrentCount,
cIdslPppoaPerfCurr15MinDiscards PerfCurrentCount,
cIdslPppoaPerfCurr1DayElapsed IdslPerfTimeElapsed,
cIdslPppoaPerfCurr1DayRTOs IdslPerfCurrDayCount,
cIdslPppoaPerfCurr1DayCVs IdslPerfCurrDayCount,
cIdslPppoaPerfCurr1DayShorts IdslPerfCurrDayCount,
cIdslPppoaPerfCurr1DayLongs IdslPerfCurrDayCount,
cIdslPppoaPerfCurr1DayDiscards IdslPerfCurrDayCount,
cIdslPppoaPerfPrev1DayMoniSecs INTEGER,
cIdslPppoaPerfPrev1DayRTOs IdslPerfPrevDayCount,
cIdslPppoaPerfPrev1DayCVs IdslPerfPrevDayCount,
cIdslPppoaPerfPrev1DayShorts IdslPerfPrevDayCount,
cIdslPppoaPerfPrev1DayLongs IdslPerfPrevDayCount,
cIdslPppoaPerfPrev1DayDiscards IdslPerfPrevDayCount
}cIdslPppoaPerfRTOs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of frames that could not be
completely reassembled due to a reassembly timeout before being
transmitted over this PPP session since agent reset."::={ cIdslPppoaPerfDataEntry 1}cIdslPppoaPerfCVs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session exhibiting a coding
violation since agent reset."::={ cIdslPppoaPerfDataEntry 2}cIdslPppoaPerfShorts OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing less than
5 octets since agent reset."::={ cIdslPppoaPerfDataEntry 3}cIdslPppoaPerfLongs OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing more than
1500 octets since agent reset."::={ cIdslPppoaPerfDataEntry 4}
cIdslPppoaPerfDiscards OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the total number of frames intended for
transmission over this PPP session that were discarded for any
reason since agent reset."::={ cIdslPppoaPerfDataEntry 5}cIdslPppoaPerfValidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of previous near-end performance data 15-minute
intervals for which data was collected. The value will be <n>
unless the measurement was (re-)started within the last (<n>*15)
minutes, in which case the value will be the number of complete
15-minute intervals for which the agent has at least some data.
In certain cases (e.g., in the case where the agent is a proxy)
it is possible that some intervals are unavailable. In this
case, this interval is the maximum interval number for which
data is available."::={ cIdslPppoaPerfDataEntry 6}
cIdslPppoaPerfInvalidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of near-end performance data 15-minute intervals in
the range from 0 to cSdslStucPerfValidIntervals for which no
data is available. This object will typically be zero except in
cases where the data for some intervals are not available (e.g.,
in proxy situations)."::={ cIdslPppoaPerfDataEntry 7}cIdslPppoaPerfCurr15MinElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslPppoaPerfDataEntry 8}cIdslPppoaPerfCurr15MinRTOs OBJECT-TYPE
SYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of frames that could not be
completely reassembled due to a reassembly timeout before being
transmitted over this PPP session in the current 15-minute
interval."::={ cIdslPppoaPerfDataEntry 9}cIdslPppoaPerfCurr15MinCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session exhibiting a coding
violation in the current 15-minute interval."::={ cIdslPppoaPerfDataEntry 10}cIdslPppoaPerfCurr15MinShorts OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing less than
5 octets in the current 15-minute interval."::={ cIdslPppoaPerfDataEntry 11}cIdslPppoaPerfCurr15MinLongs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing more than
1500 octets in the current 15-minute interval."::={ cIdslPppoaPerfDataEntry 12}cIdslPppoaPerfCurr15MinDiscards OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the total number of frames intended for
transmission over this PPP session that were discarded for any
reason in the current 15-minute interval."::={ cIdslPppoaPerfDataEntry 13}cIdslPppoaPerfCurr1DayElapsed OBJECT-TYPESYNTAX IdslPerfTimeElapsed
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will return
the maximum value."::={ cIdslPppoaPerfDataEntry 14}cIdslPppoaPerfCurr1DayRTOs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of frames that could not be
completely reassembled due to a reassembly timeout before being
transmitted over this PPP session in the current 1-day
interval."::={ cIdslPppoaPerfDataEntry 15}cIdslPppoaPerfCurr1DayCVs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session exhibiting a coding
violation in the current 1-day interval."::={ cIdslPppoaPerfDataEntry 16}cIdslPppoaPerfCurr1DayShorts OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing less than
5 octets in the current 1-day interval."::={ cIdslPppoaPerfDataEntry 17}cIdslPppoaPerfCurr1DayLongs OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing more than
1500 octets in the current 1-day interval."::={ cIdslPppoaPerfDataEntry 18}cIdslPppoaPerfCurr1DayDiscards OBJECT-TYPESYNTAX IdslPerfCurrDayCount
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the total number of frames intended for
transmission over this PPP session that were discarded for any
reason in the current 1-day interval."::={ cIdslPppoaPerfDataEntry 19}cIdslPppoaPerfPrev1DayMoniSecs OBJECT-TYPESYNTAXINTEGER(0..86400)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The amount of time in the previous 1-day interval over which
the performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not be
collected for any reason."::={ cIdslPppoaPerfDataEntry 20}cIdslPppoaPerfPrev1DayRTOs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of frames that could not be
completely reassembled due to a reassembly timeout before being
transmitted over this PPP session in the previous 1-day
interval."::={ cIdslPppoaPerfDataEntry 21}cIdslPppoaPerfPrev1DayCVs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session exhibiting a coding
violation in the previous 1-day interval."::={ cIdslPppoaPerfDataEntry 22}cIdslPppoaPerfPrev1DayShorts OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing less than
5 octets in the previous 1-day interval."::={ cIdslPppoaPerfDataEntry 23}cIdslPppoaPerfPrev1DayLongs OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing more than
1500 octets in the previous 1-day interval."::={ cIdslPppoaPerfDataEntry 24}cIdslPppoaPerfPrev1DayDiscards OBJECT-TYPESYNTAX IdslPerfPrevDayCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the total number of frames intended for
transmission over this PPP session that were discarded for any
reason in the previous 1-day interval."::={ cIdslPppoaPerfDataEntry 25}-- IDSL PPPoA Performance Interval TablecIdslPppoaIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslPppoaIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains PPPoA statistics intervals for those ITU-C
class devices configured for PPP operation."::={ ciscoIdslLineMIBObjects 17}
cIdslPppoaIntervalEntry OBJECT-TYPESYNTAX CIdslPppoaIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A 15-minute interval of PPPoA statistics intervals for a ITU-C
class device configured for PPP operation. There exists up to
96 entries for each ifEntry that meets the following criteria:
1) The ifEntry has an ifType of idsl(154);
2) The profile associated with the ITU-C class device specifies
a value of 'ppp' for the cIdslLineProtocol object."INDEX{ ifIndex, cIdslPppoaIntervalNumber }::={ cIdslPppoaIntervalTable 1}
CIdslPppoaIntervalEntry ::=SEQUENCE{
cIdslPppoaIntervalNumber INTEGER,
cIdslPppoaIntervalValidData TruthValue,
cIdslPppoaIntervalRTOs PerfIntervalCount,
cIdslPppoaIntervalCVs PerfIntervalCount,
cIdslPppoaIntervalShorts PerfIntervalCount,
cIdslPppoaIntervalLongs PerfIntervalCount,
cIdslPppoaIntervalDiscards PerfIntervalCount}cIdslPppoaIntervalNumber OBJECT-TYPESYNTAXINTEGER(1..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The interval in which the statistics were collected, where the
value of 1 represents the most recent interval, and the value of
96 represents the interval collected 24 hours ago. Intervals
2..96 are optional."::={ cIdslPppoaIntervalEntry 1}cIdslPppoaIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies whether the data for this interval
is valid."::={ cIdslPppoaIntervalEntry 2}cIdslPppoaIntervalRTOs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"This object specifies the number of frames that could not be
completely reassembled due to a reassembly timeout before being
transmitted over this PPP session in the interval."::={ cIdslPppoaIntervalEntry 3}cIdslPppoaIntervalCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session exhibiting a coding
violation in the interval."::={ cIdslPppoaIntervalEntry 4}cIdslPppoaIntervalShorts OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing less than
5 octets in the interval."::={ cIdslPppoaIntervalEntry 5}cIdslPppoaIntervalLongs OBJECT-TYPE
SYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the number of reassembled frames intended
for transmission over this PPP session containing more than
1500 octets in the interval."::={ cIdslPppoaIntervalEntry 6}cIdslPppoaIntervalDiscards OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object specifies the total number of frames intended for
transmission over this PPP session that were discarded for any
reason in the interval."::={ cIdslPppoaIntervalEntry 7}-- IDSL PPPoA VC Mapping TablecIdslPppoaMapTable OBJECT-TYPESYNTAXSEQUENCEOF CIdslPppoaMapEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table defines the mapping between PPP sessions and
ATM VC."::={ ciscoIdslLineMIBObjects 18}cIdslPppoaMapEntry OBJECT-TYPESYNTAX CIdslPppoaMapEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A mapping between a PPP session and an ATM VC. There exists an
entry for each ifEntry that meet the following criteria:
1) The ifEntry has an ifType of idsl(154);
2) The profile associated with the ITU-C class device specifies
a value of 'ppp' for the cIdslLineProtocol object."INDEX{ ifIndex }::={ cIdslPppoaMapTable 1}
CIdslPppoaMapEntry ::=SEQUENCE{
cIdslPppoaMapIfIndex InterfaceIndex,
cIdslPppoaMapVpi INTEGER,
cIdslPppoaMapVci INTEGER}cIdslPppoaMapIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The ifIndex associated with the pseudo-ATM interface
onto which the IDSL interface is being mapped."::={ cIdslPppoaMapEntry 1}cIdslPppoaMapVpi OBJECT-TYPESYNTAXINTEGER(0..4095)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The VPI (Virtual Path Identifier) associated with the ATM
VCL onto which the PPP session is being mapped."::={ cIdslPppoaMapEntry 2}cIdslPppoaMapVci OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The VCI (Virtual Circuit Identifier) associated with the
ATM VCL onto which the PPP session is being mapped."::={ cIdslPppoaMapEntry 3}-- MIB Notification DefinitionsciscoIdslLineMIBNotificationsPrefix OBJECTIDENTIFIER
::={ ciscoIdslLineMIB 2}ciscoIdslLineMIBNotifications OBJECTIDENTIFIER::={ ciscoIdslLineMIBNotificationsPrefix 0}-- MIB Conformance StatementsciscoIdslLineMIBConformance OBJECTIDENTIFIER::={ ciscoIdslLineMIB 3}ciscoIdslLineMIBCompliances OBJECTIDENTIFIER::={ ciscoIdslLineMIBConformance 1}ciscoIdslLineMIBGroups OBJECTIDENTIFIER::={ ciscoIdslLineMIBConformance 2}-- ComplianceciscoIdslLineMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities that implement the
CISCO-IDSL-LINE-MIB. Implementation of this MIB is mandatory
for any platform that supports one or more IDSL line
interfaces."MODULE-- this moduleMANDATORY-GROUPS{
cIdslBasicGroup
}GROUP cIdslPM15MinIntervalGroup
DESCRIPTION"The implementation of this group is optional."::={ ciscoIdslLineMIBCompliances 1}-- Units of ConformancecIdslBasicGroup OBJECT-GROUPOBJECTS{
cIdslLineSpecific,
cIdslLineConfProfile,
cIdslLineAlarmConfProfile,
cIdslItucInvSerialNumber,
cIdslItucInvVendorId,
cIdslItucInvVersionNumber,
cIdslItucStatus,
cIdslItucPerfCVs,
cIdslItucPerfESs,
cIdslItucPerfSESs,
cIdslItucPerfHdlcCVs,
cIdslItucPerfHdlcAborts,
cIdslItucPerfHdlcAligns,
cIdslItucPerfHdlcShorts,
cIdslItucPerfHdlcLongs,
cIdslIturPerfCVs,
cIdslIturPerfESs,
cIdslIturPerfSESs,
cIdslLineConfRate,
cIdslLineConfProtocol,
cIdslLineConfLmiProtocol,
cIdslLineConfLmiNetN392,
cIdslLineConfLmiNetN393,
cIdslLineConfLmiNetT392,
cIdslLineConfUpcIntent,
cIdslLineConfBcDefault,
cIdslPppoaPerfRTOs,
cIdslPppoaPerfCVs,
cIdslPppoaPerfShorts,
cIdslPppoaPerfLongs,
cIdslPppoaPerfDiscards,
cIdslPppoaMapIfIndex,
cIdslPppoaMapVpi,
cIdslPppoaMapVci
}STATUScurrentDESCRIPTION"A collection of managed objects defining the basic operation
of an IDSL line."::={ ciscoIdslLineMIBGroups 1}cIdslPM15MinIntervalGroup OBJECT-GROUPOBJECTS{
cIdslItucPerfValidIntervals,
cIdslItucPerfInvalidIntervals,
cIdslItucPerfCurr15MinElapsed,
cIdslItucPerfCurr15MinCVs,
cIdslItucPerfCurr15MinESs,
cIdslItucPerfCurr15MinSESs,
cIdslItucPerfCurr15MinHdlcCVs,
cIdslItucPerfCurr15MinHdlcAborts,
cIdslItucPerfCurr15MinHdlcAligns,
cIdslItucPerfCurr15MinHdlcShorts,
cIdslItucPerfCurr15MinHdlcLongs,
cIdslItucPerfCurr1DayElapsed,
cIdslItucPerfCurr1DayCVs,
cIdslItucPerfCurr1DayESs,
cIdslItucPerfCurr1DaySESs,
cIdslItucPerfCurr1DayHdlcCVs,
cIdslItucPerfCurr1DayHdlcAborts,
cIdslItucPerfCurr1DayHdlcAligns,
cIdslItucPerfCurr1DayHdlcShorts,
cIdslItucPerfCurr1DayHdlcLongs,
cIdslItucPerfPrev1DayMoniSecs,
cIdslItucPerfPrev1DayCVs,
cIdslItucPerfPrev1DayESs,
cIdslItucPerfPrev1DaySESs,
cIdslItucPerfPrev1DayHdlcCVs,
cIdslItucPerfPrev1DayHdlcAborts,
cIdslItucPerfPrev1DayHdlcAligns,
cIdslItucPerfPrev1DayHdlcShorts,
cIdslItucPerfPrev1DayHdlcLongs,
cIdslIturPerfValidIntervals,
cIdslIturPerfInvalidIntervals,
cIdslIturPerfCurr15MinElapsed,
cIdslIturPerfCurr15MinCVs,
cIdslIturPerfCurr15MinESs,
cIdslIturPerfCurr15MinSESs,
cIdslIturPerfCurr1DayElapsed,
cIdslIturPerfCurr1DayCVs,
cIdslIturPerfCurr1DayESs,
cIdslIturPerfCurr1DaySESs,
cIdslIturPerfPrev1DayMoniSecs,
cIdslIturPerfPrev1DayCVs,
cIdslIturPerfPrev1DayESs,
cIdslIturPerfPrev1DaySESs,
cIdslItucIntervalNumber,
cIdslItucIntervalValidData,
cIdslItucIntervalCVs,
cIdslItucIntervalESs,
cIdslItucIntervalSESs,
cIdslItucIntervalHdlcCVs,
cIdslItucIntervalHdlcAborts,
cIdslItucIntervalHdlcAligns,
cIdslItucIntervalHdlcShorts,
cIdslItucIntervalHdlcLongs,
cIdslIturIntervalNumber,
cIdslIturIntervalValidData,
cIdslIturIntervalCVs,
cIdslIturIntervalESs,
cIdslIturIntervalSESs,
cIdslPppoaPerfValidIntervals,
cIdslPppoaPerfInvalidIntervals,
cIdslPppoaPerfCurr15MinElapsed,
cIdslPppoaPerfCurr15MinRTOs,
cIdslPppoaPerfCurr15MinCVs,
cIdslPppoaPerfCurr15MinShorts,
cIdslPppoaPerfCurr15MinLongs,
cIdslPppoaPerfCurr15MinDiscards,
cIdslPppoaPerfCurr1DayElapsed,
cIdslPppoaPerfCurr1DayRTOs,
cIdslPppoaPerfCurr1DayCVs,
cIdslPppoaPerfCurr1DayShorts,
cIdslPppoaPerfCurr1DayLongs,
cIdslPppoaPerfCurr1DayDiscards,
cIdslPppoaPerfPrev1DayMoniSecs,
cIdslPppoaPerfPrev1DayRTOs,
cIdslPppoaPerfPrev1DayCVs,
cIdslPppoaPerfPrev1DayShorts,
cIdslPppoaPerfPrev1DayLongs,
cIdslPppoaPerfPrev1DayDiscards,
cIdslPppoaIntervalNumber,
cIdslPppoaIntervalValidData,
cIdslPppoaIntervalRTOs,
cIdslPppoaIntervalCVs,
cIdslPppoaIntervalShorts,
cIdslPppoaIntervalLongs,
cIdslPppoaIntervalDiscards
}STATUScurrentDESCRIPTION"A collection of managed objects defining performance data
collection capability using 15-minute intervals."::={ ciscoIdslLineMIBGroups 2}END